How To Start A Pilot Light On Water Heater

Your hot water heater pilot light holds tremendous power over y'all. If you lot've ever stepped into your shower on a cold winter morning — with body shivering and teeth chattering — as you wait for hot water that never comes, and then you lot know I speak the truth!

If you own a gas water heater, this can mean 1 of two things. Either (1) the gas supply has been shut off or (two) your pilot light is out. Permit's first (and quickly) deal with the possibility that your gas supply has been close off.

1. How to Make Sure Your Gas Supply is On

Detect the close-off valve to your gas line.
The shut-off valve usually is constitute close to your gas meter (see analogy beneath), which is located on the side or front of your habitation or principal edifice.
Make certain the shut-off valve continued to your gas line is in the "ON" position.
If it is non in the ON position, and so the problem is not with your gas line.
If it is in the OFF position, turn the valve to the ON position. Feel free to telephone call your local gas company for advice.

Gas meter gas line shut off valve illustration for Step 1 how to relight water heater pilot light — The first step in diagnosing the lack of hot h2o is to cheque your gas line. Make sure the gas shut-off valve is in the ON position.

If all is okay with your gas supply, so it's time to check out your water heater pilot calorie-free.

2. How to Light Your Pilot Light Water Heater

The process of relighting a pilot light is different for each manufacturer. Fortunately, there are only a few manufacturers. Your commencement step should be to look for the instructions usually glued onto your water heater. Don't worry if you can't find them. We have specific make-past-brand instructions written below.

This video contains "generalized" instructions. For instructions specific to your brand of water heater, coil below.

How to Light a Rheem Hot Water Heater Airplane pilot Low-cal

A Rheem water heater pilot calorie-free needs to exist lit manually using the piezo ignitor striker built into the h2o heater.

Rotate the gas knob on your Rheem water heater clockwise until it is in position.
Rotate the water-heater temperature punch counter-clockwise until it is set to the lowest temperature setting. Wait five minutes to let through any gas in the water.
Elevator off the outer door of your Rheem h2o heater.
Rotate the gas knob counter-clockwise until it is in the "Pilot Lite" position.
Press downwardly on the ruby push button to the left of the gas knob.
On the left of the gas knob is the piezo ignitor striker. While continuing to printing downwardly on the red button, press the piezo ignitor striker repeatedly until the airplane pilot lite is relit. You can run across the pilot calorie-free through the viewing window on the Rheem h2o heater'southward inner door.
Continue to hold downward the cherry-red push button for one infinitesimal later the airplane pilot light is lit and then release information technology. The pilot light will remain lit.
Reattach your h2o heater's outer door.
Rotate the gas knob to the "ON" position.
Set the hot water temperature punch to your preferred water temperature.

How to Lite an A.O. Smith or Country H2o Heater Airplane pilot Light

A.O. Smith water heaters and Country water heaters including the Conservationist model, utilize a piezoelectric igniter system that allows y'all to low-cal the airplane pilot by pushing the ignition push button

Take the access panel off the side of the A.O. Smith or Land water heater and set the panel out of the way.
Turn the gas control knob on the side of the water heater to the "OFF" position and allow the room to air out for approximately x minutes.
Set up the gas control knob to the "Airplane pilot Calorie-free" position. Button downwardly on the red push (this will allow the gas to flow to the burner assembly).
While standing to hold down the scarlet button, press down on the ignitor button until the airplane pilot light comes on. You may need to press downwards on the ignitor button ii or three times before the hot water heater pilot light comes dorsum on.
Hold the cherry-red button downward for well-nigh 60 seconds after the pilot is lit, then slowly allow the push button back upwards.
Turn the gas command knob to the "ON" position.
Identify the access panel back onto the side of the water heater.

How to Calorie-free a Bradford White Water Heater Airplane pilot Light

Turn the Bradford White water heater off on the control console
Allow the h2o heater sit down for 5 minutes to release gas from the system
Plough the control switch to pilot calorie-free style
Printing the ruddy control push in for a few seconds and while pressing in, button every few seconds
Listen for a click and the h2o heater status light should start blinking ignites
Allow get of the red command button
Turn the blood-red control button to the hot position.
If the pilot light does not stay lit or will not relight, a bigger problem could be the cause for your loss of hot water. Contact your plumber for immediate help.

Resource

H2o heater rubber precautions
How to restore hot water to your h2o heater
The parts of a water heater
Water heater repairs
How long does a water heater last?

Call 1-Tom-Plumber

Messing with the gas in your habitation can exist pretty scary. Don't worry, nosotros can become yous back to a warm shower in no fourth dimension. Don't hesitate to contact or call the states at one-Tom-Plumber (1-866-758-6237). We will immediately handle any emergency plumbing, drain cleaning and drain clearing, and water harm problem, including excavation of underground water lines and sewer principal lines.